|
|
|
|
| YOU ARE HERE: Home > Weldbend Catalog > Technical Data > Material Specifications (Page 2 of 2) |
| Material Specifications |
| Material | ASTM Specification | Nominal Composition | Minimum | Form | ||
| Number | Grade |
Tensile Strength |
Yield Point |
|||
| Stainless Steel | A182 |
F6 F10 F304 F310 F316 F321 F347 F348 |
13% Cr, 1% Si max. 8% Cr, 20% Ni 18% Cr, 8% Ni 25% Cr, 20% Ni 18% Cr, 12% Ni, 2-3% Mo 18% Cr, 10% Ni, Ti stabilized 18% Cr, 10% Ni, Cb stabilized 18% Cr, 8% Ni, Cb stabilized |
85,000 80,000 75,000 75,000 75,000 75,000 75,000 75,000 |
55,000 30,000 30,000 30,000 30,000 30,000 30,000 30,000 |
Forging |
| A268 |
TP410 TP430 |
11.50-13.50% Cr 14-18% Cr |
60,000 60,000 |
30,000 35,000 |
Tubular | |
| A312 |
TP304 TP309 TP310 TP316 TP317 TP321 TP347 TP348 |
18% Cr, 8% Ni 23% Cr, 12% Ni 25% Cr, 20% Ni 18% Cr, 12% Ni, 2-3% Mo 18% Cr, 12% Ni, 3-4% Mo 18% Cr, 10% Ni, Ti stabilized 18% Cr, 10% Ni, Cb stabilized 18% Cr, 8% Ni, Cb stabilized |
75,000 75,000 75,000 75,000 75,000 75,000 75,000 75,000 |
30,000 30,000 30,000 30,000 30,000 30,000 30,000 30,000 |
Tubular | |
| Wrought Iron | A42 | - - | - - - | 48,000 | 27,000 | Plate |
| A72 | - - | - - - | 40,000 | 24,000 | Tubular | |
| *5L | - - | - - - | 42,000 | 24,000 | Tubular | |
| Copper | B42 | Annealed | 99.9% Cu, 0.04% P max. | 30,000 | 9,000 | Tubular |
| Red Brass | B43 | Annealed | 84-86% Cu, 0.06% Pb max., 0.05% Fe max. | 40,000 | 12,000 | Tubular |
| Everdur 1010 | B124 | Alloy 7 | 96% Cu, 3% Si, 1% Mn | - - | - - | Forging |
| Nickel | B160 | Nickel | 99.9% Ni min. | 55,000 | 15,000 | Forging |
| B161 | Nickel | 99.9% Ni min. | 55,000 | 15,000 | Tubular | |
| Monel | B164 | Class A | 63-70% Ni, 24-31% Cu | 70,000 | 25,000 | Forging |
| B165 | - - | 63-70% Ni, 24-31% Cu | 70,000 | 28,000 | Tubular | |
| Inconel | B166 | - - | 72% Ni min., 14-17% Cr, 6-10% Fe | 80,000 | 30,000 | Forging |
| B167 | - - | 72% Ni min., 14-17% Cr, 6-10% Fe | 80,000 | 30,000 | Tubular | |
| Inconel X | - - | - - |
Nickel Base, 15% Cr, 7% Fe, 2.5% Ti, 1% (Cb + Ta), 0.7% Al |
- - | - - | Forging |
| Hastelloy B | - - | - - | Nickel Base, 28% Mo, 5.5% Fe | - - | - - | Forging |
|
ALUMINUM ALLOYS |
| Material | ASTM Specification | Nominal Composition | Temper | Tensile Strength | Yield Point | ||
| Grade | Number | Form | |||||
|
Aluminum (Figures in brackets are Aluminum Association designations) |
M1A [3003] |
B209 B210 B221 |
Plate Tubular Forging |
1.0%-1.50% Mn, balance Al |
O F |
19,000 max. 16,000 |
- - - - |
|
GS11A [6061] |
B209 B210 B221 |
Plate Tubular Forging |
0.15%-0.40% Cu, 0.8-1.2% Mg, 0.15-0.35% Cr, balance Al |
O F T6 |
22,000 max. 30,000 nom. 38,000 |
16,000 max. 16,000 nom. 35,000 |
|
|
CG42A [2024] |
B209 B210 B221 |
Plate Tubular Forging |
0.3-0.9% Mn, 1.2-1.8% Mg, 3.8-4.9% Cu, balance Al |
O T4 |
35,000 max. 57,000- 70,000** |
19,000 max. 42,000- 52,000** |
|
|
GR20A [5052] |
B209 B210 |
Plate Tubular |
2.2-2.8% Mg, 0.15-0.35% Cr, balance Al |
O | 35,000 max. | - - | |
|
CS41A [2014] |
B221 | Forging |
0.4-1.2% Mn, 3.9-5.0% Cu, 0.2-0.8% Mg, balance Al |
O T6 |
30,000 max. 60,000 - 68,000** |
18,000 max. 53,000 - 60,000** |
|
| * Dependent upon wall thickness | |
| www.weldbend.com | Copyright © 2002 by Weldbend Corporation. All Rights Reserved. |
